Left direction
STD - Safe Time Delay
STD - Safe Time Delay
SLN V4.2
SLN V4.2
Slimline RHD
Slimline RHD
Slimline EVD V4.0
Slimline EVD V4.0
Impact Remote Head
Impact Remote Head
Failsafe Bypass Unit
Failsafe Bypass Unit
EVD V4.0
EVD V4.0
ERS/EVD
ERS/EVD
EPEG V2
EPEG V2
Cryptocode V2.0
Cryptocode V2.0
ATM8
ATM8
ATM7
ATM7
ATM6
ATM6
ATM Interlock Override
ATM Interlock Override
Right direction
You are here: Home arrow High Security Products arrow ATM8
  • Decrease font size
  • Default font size
  • Increase font size



 ATM8
Item Code : JS246
Title : ATM8
Application : Vibration detector for the Wincor-Nixdorf ProCash 2050xe
PDF Specification Sheet: Download Now

OVERVIEW

The ATM8 (Automated Teller Machine) vibration detector has been designed specifically for use on the Wincor-Nixdorf ProCash 2050xe. The ATM8 comprises an advanced signal processing analyser (EVD –Explosion Vibration Detector) and electromechanical release mechanism housed within a robust steel enclosure. This combination offers sophisticated attack detection and controlled access to the protected unit by an authorised user.

The illustration above shows the ATM8 and its companion magnet hasp, the latter is fitted to the leading edge of the door. When the door is closed the magnet is concealed under the lid of the ATM8 and door status can be monitored. To allow access to the safe, a low-voltage DC supply is applied to the ATM8 – indicated by a green LED. The authorised user presses the release switch and the lid of the ATM8 can be opened (limited travel) thereby freeing the magnet and allowing the safe door to be opened. In addition to dual anti-tamper protection (single output), the ATM8 offers a number of additional outputs: -
  • VIBRATION. Attack by way of drilling, grinding, hammering or thermal cutting device (when operated in conjunction with a JS161, SLN) will trigger the VIB output.
  • IMPACT. Explosives, a series of consistent strikes or attempts at ram-raid will activate the IMP output instantly.
  • TILT. Any attempt to move the protected equipment will activate the TILT output. In addition, high-energy attacks such as ATM ram-raid will also trigger this output.
  • DOOR. A voltage-free contact that reports the state of the safe door.
  • SLIDE. A voltage-free contact indicating if the ATM8 cover is opened/closed.
The principle function of the ATM8 is signal processing and analysis of the various on-board sensors then to take appropriate action in the event of a legitimate attack. In addition, this unit has a number of dedicated inputs that support remote sensors that enhance and extend the area of coverage. Typical of this are products JS161, SLN (Smoke Light Noise) unit and JS195 RHD (Remote Head).

KEY FEATURES
  • Advanced signal-processing scheme.
  • Separate alarm outputs.
  • On-board LED indication for Signal Detect, Vibration Alarm and Impact Alarm.
  • Low level Impact and Explosion sense capability.
  • Nominal 3m2 detection zone.
  • Improved power consumption over earlier variants.
  • Extended coverage when used with remote head(s).
  • Sensitivity adjustment for non-standard installations.
  • Robust 1.2mm seam welded mild steel enclosure.
  • Enclosure anti-tamper.
  • Easy to install – no set-up required.
ELECTRICAL & MECHANICAL DATA

Analyser supply voltage: 12 Volts DC (nom)
Analyser operating voltage range: 10.5 – 15.0 Volts DC
Analyser quiescent Current: 28 mA @ 12 Volts DC
Maximum analyser current consumption: 42 mA @12 Volts DC
Solenoid supply voltage: 12 Volts DC (nom)
Solenoid operating voltage range: 10.5 – 15.0 Volts DC
Continuous solenoid current consumption: 500 mA (approx) @ 12 Volts DC
Maximum ATM8 current consumption: 542 mA (approx) @ 12 Volts DC
Please note. The power supply should be capable of handling a peak load of 1.2 A @ 12 V DC to accommodate the solenoid inrush current.
Maximum detection area: 3 m2
Operating temperature range: -10oC to +40oC
Outputs: Voltage-free contacts rated at 0.1 A @ 12 Volts DC for VIBRATION, IMPACT, TILT, DOOR, TAMPER, SLIDE
Construction: 1.2 mm seam welded mild steel
Main body dimensions (mm): 265.0 (L) x 102.0(1) (W) x 90.5(2) (D)
(1)Allow an extra 7.0 mm for hinge screw protrusion.
(2)This dimension includes the right-angle return. Also, please allow an extra 20.0 mm for the lid handle.
Hasp dimensions (mm): 78.0 (L) x 15.5 (W) x 15.5 (D)
Main body weight: 2.15 Kg
Hasp weight: 0.04 Kg
Cable entries: 2 off 16mm hinge side entry
Colour/Finish: Dark Grey / Powder coat



Technical Data

If you require more technical data regarding any of our products then please follow this link. 

Data Request